Emporia, KS 66801
Topeka, KS 66609
Sedalia, MO 65301
Enid, OK 73703
Manhattan, KS 66502
Hiawatha, KS 66434
Topeka KS 66604
Maryville, MO 64468
Kirksville, MO 63501
Grand Island, NE 68803
Premium Glueless Luxury Vinyl planks are constructed with the patented Uniclic® interlocking joint that locks the planks together to form a tight, durable, water resistant joint. Premium Glueless LVT flooring is installed as a floating floor so it’s quick and easy to install with no adhesive required. All you need is a smooth dry surface and a few basic hand tools.Once the floor is installed it can receive traffic immediately.
Planks can be installed over a variety of subfloor surfaces including concrete on all grade levels, wood and many existing hard surface floors. The subfloors must be clean, smooth, flat, solid and dry. Do not install planks over floors that are sloped for drainage. Any uneven areas greater than 1/16” in 3’ should be leveled with a portland cement based patching compound. Vinyl tiles are resistant to water damage but they do not prevent the transmission of moisture. Care should be taken to keep moisture from collecting on either side of the vinyl floor to prevent the growth of mold and mildew.
Premium Glueless LVT planks are suitable for installation over double layer wood subfloors that are a minimum of 1” thick, or single layer subfloors constructed with APA rated Sturd-I-Floor panels, 23/32” or heavier. Joist spacing should not exceed 19.2”. Set fasteners 1/32” below the subfloor surface, sand joints smooth and fill holes and gaps wider than 1/8” wide. Install suitable underlayment when necessary to achieve a flat or solid surface. Premium Glueless LVT planks can be installed over underlayment grade plywood, lauan plywood and other underlayments recommended by the manufacturer for use with luxury vinyl plank. Installation over oriented stand board and particle board is not recommended since these panels presents a greater risk of sub-floor instability and can detract from the performance of the floor. Wooden subfloors installed over a crawlspace should have a moisture barrier installed in the crawlspace with at least 18 inches of ground clearance.
NOTE: Avoid subfloors with excessive vertical movement or deflection because subfloor movement will telegraph through to the finished installation. Indications of excessive deflection are subfloor fastener release, squeaking, compromised or sectional contours such as bowing or dipping in floors and uneven flooring material. Nail or screw subfloor panels to secure boards with excessive vertical movement or deflection prior to installation of the Premium Glueless LVT planks. If the subfloor has excessive vertical movement (deflection) before installation of the flooring, it is likely it will do so after installation of the flooring is complete. Our warranties DO NOT cover any problems caused by inadequate substructures or improper installation of said substructures.
Premium Glueless LVT planks can be installed over concrete on all grade levels, if a proper moisture barrier is used. Moisture vapor emissions should not exceed 5 lbs./24 hour per 1,000 sq. when tested with the Anhydrous Calcium Chloride Test in accordance with ASTM F 1869 or 80% RH in accordance with ASTM F 2170 “Standard Test Method for Determining Relative Humidity in Concrete Slabs using in situ Probes. A 6 mil polyurethane moisture barrier should be used with concrete subfloors. Fill cracks; saw cuts and control joints and level uneven areas that exceed 1/16” in 3’. Do not install flooring over expansion joints.
Premium Glueless LVT planks can be installed over a variety of finished floors including single layer resilient sheet floor and tile, ceramic, marble and terrazzo. The surface must be in good condition and show no signs of excessive moisture conditions. Level deep or wide grout lines with embossing leveler. Do not install flooring over heavily cushioned floors or over tile installed over concrete below grade level. The grout joints in ceramic tile and marble must be leveled so they are flush with the tile surface. Additionally the tile may require several skim coats to achieve a flat surface.
Premium Glueless LVT planks can be installed over in-floor radiant heating systems provided the subfloor surface does not exceed 85F at any point. The initial floor temperature should not exceed 70F for 24 hours prior to and 48 hours after installation. Thereafter the temperature should be gradually increased to the desired setting up to 85F. Radiant heating systems that are installed on top of the subfloor surface and covered with self-leveling underlayment are not recommend.
WARNING! DO NOT MECHANICALLY CHIP OR PULVERIZE EXISTING RESILIENT FLOORING, BACKING, LINING FELT, ASPHALTIC “CUTBACK” ADHESIVES OR OTHER ADHESIVES. Previously installed resilient floor covering products and the asphaltic or cutback adhesives used to install them may contain either asbestos fibers and/or crystalline silica. The products in this carton DO NOT contain asbestos or crystalline silica. Avoid creating dust. Inhalation of asbestos or crystalline dust is a cancer and respiratory tract hazard. Smoking by individuals exposed to asbestos fibers greatly increases the risk of serious bodily harm. Unless positively certain that the previously installed product is a non-asbestos containing material, you must presume it contains asbestos. Regulations may require that the material be tested to determine asbestos content and may govern the removal and disposal of material. See current edition of the Resilient Floor Covering Institute (RFCI) publication “Recommended Work Practices for Removal of Resilient Floor Coverings” for detailed information and instructions on removing all resilient covering structures.
When the LVT planks are installed in a bathroom the flooring can be laid under the toilet only if the floor is separated from adjacent rooms with a doorway threshold. Otherwise the flooring should be installed around the toilet leaving a 1/8” expansion space. Use a high quality silicone caulking to fill the expansion space at the tub, shower and all wet areas to prevent surface water seepage under the floor.
Premium Glueless Luxury Vinyl Tile is not recommended for use on stairs or steps.
Remove all spacers. Install wall trim lightly over the floor surface. Drive fasteners into the wall and not the floor. When installing doorway transition moldings allow a ¼” expansion space between the edge of the floor and the molding. Do not drive fasteners in to the floor. Return appliances to the room by rolling or sliding over strips of hardboard to prevent damaging the floor.